A four layer lamination tested for use in retort applications. lamination incorporating RCPP sealant layer, Foil, and BOPA Nylon with an outer Pet printing layer. May be suitable for high performance requirement environments such as freezing, retort, and extended shelf life. This film is a modified version of our PET/AL/LLDPE CareFoil material.
The film has heat resistance which has been tested to meet FDA standards for polypropylene and polyethylene used in articles that contact food. Meets SGS, FDA,QS, EC standards.
Note: The performance of any film will be influenced by a number of factors and testing must always be performed to ensure the film meets the use.
Here are some of the common indicated properties for this film.
VALUE / RESULT / INDICATION
Final Material Composition
Common Available Thickness Range
Width Deviation of heat seal
Long 57 N | Landscape 57 N
Elongation at Break
159 % / 96%
Right Angle Tear
13.1N | 13.3 N
8.5N | 9.1 N
Anti-Pendulum Impact Strength
29.9N | 29.1 N
3.74 g/(㎡·24h) 38C @ 90%RH
44.8 ㎝³/(㎡·24h·0.1MPa) 23C @ 40%RH)
Tensile force change rate 0.97 elongation force change 7.1
Pass 140g load 400N 1min
Pass 140g 500mm
Evaporation residue; 65% Acetic acid
Pass No Odor, Turbidity and discoloration
Evaporation residue; 65% Ethanol
Evaporation residue; Ethane
Heavy metal (Pb) 4% Acetic acid
Toluene diamine(4% Acetic acid)
Extractable fraction in n-hexane
Soluble fraction in xylene
All values indicated regarding film properties or characteristics, were provided by our film supplier and are given as an indication and should be considered as average indicative values. This document is based on our film supplier statements and / or independent lab testing, data from multiple tests, or different film suppliers of the same film family may be combined in the above table. While unexpected, it is possible that the validity of the statements could change without notice.
This material is a multi-layer laminated plastic and will typically fall into the check-locally, or store drop off category.
Multi-Layer Check Locally
PCR Option Available
At Home Compostable
Commercial / Industrial Compostable
Recyclability and composability varies by jurisdiction. Composability claims are limited by law, and vary by jurisdiction, consult a qualified professional in your state.
Compliance is important, and here are CarePac we can support your compliance needs with extensive film supplier and lab testing data.
FDA Food Approved
Manufactured in accordance with
Cal. H&S (25214.16)
PFAS - perfluoroalkyl and polyfluoroalkyl § 37-0209, RCW 70A.222.070
Does not knowingly add
Prop 65 (OEHHA)
Does not contain listed substances
Not in excess of overall or specific migration
EU directive 10/2011/ED
EU directive 1935/2004
FDA 21 CFR 73
Cal. H&S (25214.16)
RoHS Directive 2011/65/EU
Compliance information above is derived from lab testing, or film supplier statements. Independent verification is advised, and Lot specific testing available.
CareFoil-PAP is our high barrier film structure which incorporates encapsulated aluminum foil as the barrier layer of this film. The exterior high grade PET serves as a great base for printed bags. The interior PE sealant layer is non-reactive and is heat sealable. CareFoil-PAP is great for FDA applications where long shelf life, or susceptibility to spoilage is a concern.
This material has a higher than average moisture and strength, with good oxygen and gas barrier. As this is a clear product it has limited light barrier potential but does have good heat resistance. Enhanced heat resistance could be obtained with CareClear-PNC is required by the use application.